Cast Nosings ALUMOGRIT® or FERROGRIT®

ALUMOGRIT® and FERROGRIT® cast nosings

Wooster’s quality cast nosings contain an even distribution of abrasive grit integrally cast into the surface for anti-slip protection and long wear.
Width and length to order.
Available in ALUMOGRIT® (abrasive cast aluminum) and in FERROGRIT® (abrasive cast iron).

Specifications / Guidelines for Installation / Fasteners
Leed(Alumogrit®) / Leed(Ferrogrit®)

Specify abrasive cast nosing for:

  • Maximum Durability in Rough Use
  • Indoor or Outdoor Use
  • Resistance to Unusually Corrosive Environments
  • Anti-Slip Safety Properties
  • Ready to Install Convenience
  • New Construction or Existing Buildings

Surface: Abrasive cross-hatch is standard and will be furnished unless plain or fluted surface is specified. (Cross-hatch pattern may not match up on sections being butted together.)
Fasteners: Concealed integral anchors or steel wing anchors, nuts and bolts for wet concrete. Or drilled and countersunk holes for other fasteners.
Length: Maximum length is 8’6″ in ALUMOGRIT® (abrasive cast aluminum) and 6’0″ in FERROGRIT® (abrasive cast iron) for most type but see individual type for additional information.
Width: Standard widths are 3″, 4″ and 6″. Standard measurements are from top of the leading edge.

ALUMOGRIT® or FERROGRIT® Type 101
ALUMOGRIT® or FERROGRIT® Type 101
ALUMOGRIT® or FERROGRIT® Type 101
Chief use: as nosings in concrete stairs
$0.00
ALUMOGRIT® or FERROGRIT® Type 101SP
ALUMOGRIT® or FERROGRIT® Type 101SP
ALUMOGRIT® or FERROGRIT® Type 101SP
Chief use: as nosings in steel-pan concrete-filled stairs
$0.00
ALUMOGRIT® or FERROGRIT® Type 102
ALUMOGRIT® or FERROGRIT® Type 102
ALUMOGRIT® or FERROGRIT® Type 102
Chief use: as nosings on steel-pan stairs. Can also be used structurally with bent-plate risers.
$0.00
ALUMOGRIT® or FERROGRIT® Type 103
ALUMOGRIT® or FERROGRIT® Type 103
ALUMOGRIT® or FERROGRIT® Type 103
Chief use: as structural treads with bent-plate risers or as nosings full width of stair.
$0.00
ALUMOGRIT® or FERROGRIT® Type 116
ALUMOGRIT® or FERROGRIT® Type 116
ALUMOGRIT® or FERROGRIT® Type 116
Chief use: as nosings in concrete stairs where deeper lip is desirable
$0.00
ALUMOGRIT® or FERROGRIT® Type 116A
ALUMOGRIT® or FERROGRIT® Type 116A
ALUMOGRIT® or FERROGRIT® Type 116A
FOR EXISTING STAIR REPAIR - Chief use: on top of existing steps for repair and modernization.
$0.00
ALUMOGRIT® or FERROGRIT® Type 100
ALUMOGRIT® or FERROGRIT® Type 100
ALUMOGRIT® or FERROGRIT® Type 100
Chief uses: floor plates, trench covers, stair landing platforms, expansion joint covers.
$0.00
ALUMOGRIT® or FERROGRIT® Type 110
ALUMOGRIT® or FERROGRIT® Type 110
ALUMOGRIT® or FERROGRIT® Type 110
Chief uses: Expansion joint covers, platforms around machinery, deck treads.
$0.00
ALUMOGRIT® or FERROGRIT® Type 120
ALUMOGRIT® or FERROGRIT® Type 120
ALUMOGRIT® or FERROGRIT® Type 120
Chief uses: nosings on steel grating treads and for special conditions, usually superimposed.
$0.00
ALUMOGRIT® or FERROGRIT® Type 150
ALUMOGRIT® or FERROGRIT® Type 150
ALUMOGRIT® or FERROGRIT® Type 150
Type 150 Concrete Curb Bar 1-1/2" x 1-1/2"
$0.00
ALUMOGRIT® or FERROGRIT® Type 250
ALUMOGRIT® or FERROGRIT® Type 250
ALUMOGRIT® or FERROGRIT® Type 250
Type 250 Concrete Curb Bar 2-1/2" x 2-1/2"
$0.00
ALUMOGRIT® Type 950
ALUMOGRIT® Type 950
ALUMOGRIT® Type 950
Type 950 ladder rung 2" x 18" Alumogrit® only
$0.00
ALUMOGRIT® or FERROGRIT® Type 104
ALUMOGRIT® or FERROGRIT® Type 104
ALUMOGRIT® or FERROGRIT® Type 104
Nose 1″ X 1″ Chief use: as structural treads with bent-plate risers or superimposed on existing steps.
$0.00
ALUMOGRIT® or FERROGRIT® Type 105A
ALUMOGRIT® or FERROGRIT® Type 105A
ALUMOGRIT® or FERROGRIT® Type 105A
Nose 1″ X 1-1/2″ Chief use: as structural treads with bent-plate risers or superimposed on existing steps.
$0.00